Showing posts with label looms - countermarche. Show all posts
Showing posts with label looms - countermarche. Show all posts

Thursday, June 04, 2026

How To Make a Repair (Replacement) Heddle on a Glimakra Loom

 At last, I tied up the treadles for the new leaf motif draft and was ready to weave my header. Lo and behold, I had another threading error! I honestly think part of the problem is my bifocals. Even with progressive lenses, it's difficult to get that sweet spot for several activities, such as heddle threading and painting ceilings. I even have trouble viewing my computer screen comfortably. 

I had skipped a heddle, so I searched about for how to add another heddle in the middle of the shaft. I ran across this video by Underwood Textile Arts. I'm embedding it here, for future reference! 


EDIT to add a link to Peggy Osterkamp's latest blog post, Repair Heddles: New (to me) Methods. It looks like another easy method for adding Texsolv heddles.

Sunday, May 24, 2026

Leaf Motif Draft: There's a Problem

I found the leaf motif draft on handweaving.net. The original draft for this was 8 shafts and 30 treadles. (The links in the caption are to document the source. This will take you to a drawdown if you don't have an account. You have to have a paid account to see the full draft.)

Original: Draft #80360: 8-shaft version of 79845, 2004-2026

Someone later reduced it from 30 to 10 treadles.

Modified: Draft #80362: 8-shaft version#80360; reduced to 10 treadles, Ruth Barbour, 2004-2026

The reduced version requires pressing two treadles per shed. My problem is the mechanics of the countermarch loom, where the shed (opening in the warp to pass the shuttle through) is created by lifting some shafts and lowering the rest. Each shaft is tied to each treadle to go either up or down, depending on the tie-up pattern. In this leaf draft, the treadling pattern requires using treadles simultaneously that have shafts tied opposite. I can't raise and lower a shaft at the same time!

For some reason my brain did not catch this. It feels like it should have been obvious, except it wasn't. I think it's one of those things I had to relearn. (After a 17 year break from weaving, I'm finding there are lots of things in the relearn department.)

So. 

It would probably work on an 8-shaft jack loom, because on a jack loom only the rising shafts are tied. Except I don't have an 8-shaft jack loom

I could try a skeleton tie-up. Except I'm not sure I could manage to press four treadles at the same time. 

I could look for a different draft. Which is where I'm at now. The warp is already on, with a point twill threading, so I need to find a draft that will work with that and requires only one treadle at a time!

Stay tuned. 

© 2026  by Leigh at Leigh's Fiber Journal

Wednesday, May 20, 2026

Lamm-Top Treadle Tie-up

At last, the Leaf Motif warp was on the loom and it was time to tie up the treadles. For a countermarch loom like my Glimakra, that used to mean many back-breaking hours on the floor hunching over the treadles. It meant rearranging and rethreading all the treadle cords for each new draft. I have a step-by-step in this post -> Dressing the Glimakra B2F Step 5: Tying Up the Lamms & Treadles.        

Then I learned about a method of tying up countermarch treadles from the top of the lamms. I had to give it a try. Here are my blog posts about what I learned and how I set up my loom for it:

And here's a photo of what it looked like when I was done, ready to tie up the treadles.


This is a permanent arrangement. I no longer have to change all the cords according to length for each draft. Attaching the treadles to the correct lamms is done from the top.

I've always tied up the treadles as the last step in dressing the loom, so the warp already tied to the front. With the lamm-top tie-up it's possible to attach the treadles before securing and tensioning the warp. So this time, I had to do my tie-up from the back of the loom, where my bench was already set up for heddle threading. It probably would be easier if done from the front, with the cloth and knee beams removed for easy access to the lamms. I'll try that next time.


I made a grid on an index card and diagrammed the tie-up from the draft. On the diagram, I numbered my shafts and treadles, and made a note for the marks on the cord. 


The marks indicate where to put the anchor pegs. 
  • Shafts 1, 2, 3 use the top mark.
  • Shafts 4, 5, 6 use the middle mark.
  • Shafts 7, 8 use the bottom mark.



They can be adjusted as needed for an even shed. Here's what it looked like when I was done. 


Next, I'll pull the locking pins from the countermarch and make sure everything is level. Then I'll be ready to start weaving. I have two weights of weft yarn, so I'll be sampling those first. 

Sunday, June 08, 2025

Treadle Tie-Up From the Top: Installing the Texsolv Cords

8 bunches of 10 cords each

This will be the last time I will have to get down on the floor and hunch over to thread the treadles and lamms! Once I'm done, the cords will be a permanent fixture and easy to arrange from the top on a comfortable seat. No more backache!

Each cord is threaded through the bottom of each treadle hole, where the pony bead secures it.

up through the lower lamm holes, 

then up through the upper lamm holes, and knotted at the end so they don't slip back down. 

Here's what it looks like with all the cords in place.


Next, I need a warp on the loom to try out my new tie-up method. I have a project in mind, but harvest and canning season is heavy upon us. Warping the loom will have to wait until I have some free time. 

Thursday, May 29, 2025

Treadle Tie-Up From the Top: Preparing the Texsolv Cords

 To set up my 8-shaft Glimakra for tying up the treadles from the tops of the lamms, I need 80 lengths of Texsolv cord. The first step was to determine their length. 

The measurement from floor to the top of the upper lamm is 23 inches. Then I need to allow for knotting the cord at both top and bottom. Using the Vavstuga idea of securing the cords under the treadles with pony beads . . . 


 . . . requires about 4 "buttonholes" of cord, which is about 2 inches.

I'll also need to knot the cord at the other end, to keep it from slipping back down through the upper lamm hole. That takes about 1.5 inches. The other option would to be to put a peg into the end buttonhole, which could be moved if the lamm was needed. Anyway, I added 3.5 inches to my measurement of 23 inches. Plus, I need enough cord to grab it and work with it, so it looks like Jean's measurement of 28 inches per cord length sounds about right. 

If I make my cord lengths 28 inches, then my 55 yard spool of Texsolv cord will give me 70 lengths. My partial spool gives me 4 more. Scrounging around in my box of Texsolv cord scraps, I found the remaining 6 that I'll need, so I'm good to go!

To measure and cut the cords, I used a board with two finishing nails as a jig. 


Total length is 28 inches, which includes half a buttonhole on each end.

Both Kati and Jean tell you how to mark the jig for marking the cord to pin for each lamm. Since I used Jean's 28-inch measurement, I also used her marking recommendation. You can see the chart at her website. 


The placement of the marks is for anchor pegging the cords to the lamms, which I'll show when I get to that step. After I mark each cord, I'm attaching a pony bead to the treadle end.

I'm cutting 8 bundles of 10 heddles each. Then I'll secure a pony bead on the end of each one and can begin to insert the cords through treadles and lamms.

The other thing that occurred to me is that I don't actually need an anchor pin for every hole on both lamms. Each treadle is tied to only one lamm, either the upper or the lower, so technically I'll only need 80 anchor pins. It would be convenient to have a set for both upper and lower lamms, but this way I won't need to buy more. Nor will I need to get push pins. I can live with that. 

Saturday, May 24, 2025

Treadle Tie-Up From the Top: What I'll Need

 Even though I understood the concept in my head, the particulars of the "from the top" tie-up (aka "Top O' the Lamm") were a bit puzzling at first. I have both Kati Meek's Complex Weaver's Journal article and Jean Elizabeth Studio blog post (see my resources post for details), but even though they were both using Glimakra Standard looms like mine, their measurements vary just a bit. 

The first thing I did was to measure my loom from the floor to the top of the upper lamm.

23 inches from the floor to the top of the upper lamm.

The idea is to cut the Texsolv cords so that if a treadle is resting on the floor, there is still enough length above the top lamm to pin the cord as needed. Kati cut her cords at 25 inches, while Jean cut hers at 28. 

The next step was figure out how much Texsolv cord I'll need. The cords will run from the bottom of the treadles, up through the lower lamm holes and then the upper lamm holes, with enough cord to secure each so that it doesn't slip back through. I have 10 treadles with 8 holes each (one for each shaft) so I'll need a total of 80 cords cut the same length. 

If I go with the 25 inch length, I'll need 55.5 yards of Texsolv cord. I have a new, full spool which is 55 yards! Sheesh. But I also have a few yards left on an old spool, so I should be good to go there.

I'll also need 240 Texsolv pegs (pins).

Texsolv "buttonhole" cord and anchor pins. They also make an
"arrow" pin, but these are the ones I have so that's what I'll use.

I'll need one for each of the treadle holes, lower lamm holes, and upper lamm holes. After removing all of the old treadle cords, I find I have only 105! At $16 per 25 anchor pegs, I'm considering alternatives for at least some of them.

Jean used pony beads to secure the cord under the treadles (see her blog post for photos). If I do that I'll only need 160 anchor pegs. But also, I found a video on how to use push pins to make substitutes.

Texsolv Cord Pegs - Weaving Hack! Alternative to Pegs

Push pins are certainly less expensive, and there are a number of places I can substitute them. 

After I get some pony beads and push pins, I'll be ready to get started. 

© 2025  by Leigh at Leigh's Fiber Journal

Related posts

Tuesday, May 20, 2025

Treadle Tie-Up From the Top For My Glimakra: Resources

 As much as I love weaving on my countermarch loom, tying up the lamms and treadles is a real pain. Or at least it's extremely uncomfortable as it involves crawling around on the floor and contorting to connect everything in the right pattern. So when I ran across a video series on how to tie up a countermarch loom easily from the top, I was immediately interested. This post is to list whatever resources I found on how to do it.

The first resource an article by Kati Meeks in the October 2017 issue of Complex Weaver's Journal. I found back issues available on the Complex Weavers website, and ordered a copy. This is the article that started the system.

Next is a link to a blog post at Jean Elizabeth Studio:

Top O’ The Lamm Tie-up

And here is a list of videos from Jean Elizabeth Studio. These were made to clarify the blog post:

Top O' The Lamm Tie Up for Countermarch

Top O' The Lamm Tie Up for Countermarch Part 2

Correction for markings on Texsolv - Top O' The Lamm Tie Up for Countermarch  

More Top O' The Lamm Tie-Up and Sleying the Reed

Also, I found a few more pictures at: 

Kay Faulkner's blog, A convenient treadle tie up method for countermarche looms

Kati Meeks blog, I am re-draw-loomed And having a blast!

So that's what I have to work with for instructions. If I find additional resources, I'll add them too.


Related post

Friday, May 31, 2024

Dressing the Glimakra B2F Step 6: Checking the Shed, Weaving a Header

Continued from Dressing the Glimakra B2F Step 5: Tying Up the Lamms & Treadles

Remove the countermarch locking pins

The locking pins keep the jacks (and everything else) from moving.

The shafts shouldn't drop more than slightly.

Evaluate the shed

This involves weaving a couple shots and then pressing each treadle in turn to check the levelness of the bottom of the shed. 

Adjustments needed on both bottom and top

Fortunately, I took good notes on adjusting the shed the first time I set up the Glimakra. That post is here. Plus, I have Joanne Hall's Tying Up the Countermarch Loom (book review here). The summary of the process as follows.

All adjustments to a countermarch loom start at the top. 
  • With locking pins in place, check:
    • That the shafts are centered to the loom. 
    • That the warp runs through the center of the heddle eyes. If it doesn't, then the shafts need to be raised or lowered accordingly by adjusting the cord on the anchor pins on the jacks at the top of the countermarch.
    • That the beater height allows the shed to run through the middle of the reed.
    • That the lamms are level with one another. Adjust if necessary.
  • Remove the locking pins
    • Depress each treadle in turn and examine the shed. 
    • If all the warp ends are level, that's it.
    • If some of them are above or below the others, make notes of which shaft they are on.
To adjust the shed, replace the countermarch locking pins.
  • To adjust the bottom threads of the shed:
    • Start by adjusting treadle cords at the upper lamms. Use your notes.
    • For shafts with warp threads that are too high, shorten the treadle ties.
    • For shafts with warp ends that are below the shed, lengthen the treadle ties.
    • Remove the locking pins and check again. Make more adjustments needed.
  • To adjust the top of the shed:
    • Adjust the treadle cords at the lower lamms, using your list.
    • For threads that run too high, lengthen the treadle ties.
    • For threads that run too low, shorten the treadle ties.
    • Recheck and repeat if needed.
    • Note that this is opposite of what was done with the upper lamms.

Note: Treadles don't have to be even in height.

Weave the header

Couldn't help but be a little nervous. Did I get my shed adjustments right? Did I make any threading mistakes? I caught a few when I sleyed the reed. Did I get the tension even across the warp? I'll find out now!


Things to check:
  • Shed: good
  • Treadle height: comfortable
  • Fell line: straight
  • Threading errors: the only "error" turned out to be a dropped treadle cord
  • The ski shuttle worked well

Next time should go more quickly. For one thing, the shafts and lamms should need no further adjustment in the future. Plus, with this warp, I spent a lot of time researching, reading, re-reading, and comparing notes from various sources. For future reference, I have this blog series to refer to. 

And with that, I'm ready to weave.

Monday, May 27, 2024

Dressing the Glimakra B2F Step 5: Tying Up the Lamms & Treadles

Continued from Dressing the Glimakra B2F Step 4: Threading, Sleying, Lashing On 

Tying up the treadles of a countermarch is a big job. The popular jack loom requires only tying up the shafts that rise. With my Schacht Mighty Wolf, treadle tie-up was just a matter of sliding the required shaft cords into the slot on the appropriate treadle. (There's a photo at the top of this post.)

A countermarch, on the other hand, engages all shafts; some rise and the other sink. That means all treadles have to be connected to all shafts. An 8-shaft loom like mine has 8 shafts times 10 treadles. So 80 individual cords need to be attached to the treadles. 

I've got three ways to tie up the treadles of a countermarch loom. Two I've tried, and one I plan to try soon. I'll update this post then.

Preliminary steps

  • Check position of warp
    • Should be centered in the reed and heddle eyes
    • Adjust shafts and beater height as necessary
  • Check the lamms*
    • Should be level and even in height.
    • Adjust if necessary

* Because this is my first warp after re-assembling the loom, tweaking the lamm tie-up and shaft placement should be a one-time job. Once set, future warps shouldn't need it.

The tie-up draft

Example tie-up draft for a countermarch loom

Reading the draft
  • Rows represent the shafts with the bottom being #1. The top row is shaft #8
  • Columns represent the treadles.
  • Xs and Os represent which shafts rise and which shafts sink.
  • Memory tricks for reading CM drafts
    • X as in X marks the spot (to sink the shovel)
    • O are shaped like bubbles which rise

Converting a draft

Most sources will tell you if it's a rising or sinking shed loom draft. If they don't, it's likely a rising shed draft because most American weavers have rising shed (jack) looms. You can make your own CM tie-up draft on graph paper.
  • Fill in the rising shaft squares on the graph with Os.
  • Fill in the remaining graph squares with Xs.
For a sinking shed tie-up (counterbalance loom) 
  • Fill in the sinkng shaft squares on the graph with Xs.
  • Fill in the remaining graph squares with Os.


Tying up the lamms

The lamms are the levers that control whether the shafts rise or sink.

Upper lamms
  • The shorter set of lamms
  • Function to lower the shafts
  • Memory aid: smaller sink
  • Designated by an X on the tie-up draft

 Lower lamms

  • The longer set of lamms
  • Function to raise the shafts
  • Memory aid: lower lift  
  • Designated by an O (or blank) on the tie-up draft
With draft in hand, I start by putting anchor pegs in the holes that don't need to be tied up. So on the upper lamms, I put pegs in the Os. On the lower lamms, I put pegs in the Xs. Then all I need to do is to put the lamm ties in the empty holes.

Tip: a dab of glue on the ends of the ties stiffens them so that it's easier to thread them through the lamms and treadles.

It looks like this when I'm done.

I double check the tie-up when I drop the treadle cords down in front of the each corresponding lower lamm. Each cord should have an empty lamm hole directly beneath it.

Treadle tie-up method 1: traditional

The cords are secured on the bottom of the treadle, with each lamm tie inserted through the corresponding hole in the treadle. 

Loom set-up

Treadles lifted at a height of 6 - 8 inches.

Start with the ties near the back of the loom, which need to be tightest. This is because the angle of the pressed treadle is narrowest at the back of the loom, but sharpest at the front of the loom. Hence more treadle cord is required.

Done. Distance between moving parts (treadles, lamms, & shafts) should be equally spaced.

Advantage to method 1

  • Carries on the tradition of countermarch looms. (Not sure if that's an actual advantage, but I had to think of something positive to say.)

Disadvantages

  • Tie-up for lamms and treadles must be changed for each new draft
  • Time consuming
  • Tiring on the back
  • Poking the pegs of the anchor pins into the underside of the treadles must be done by touch.
  • Requires patience

Method 2: skeleton tie-up

Shortly after I got my Glimakra, I started using a skeleton tie-up. Like the table loom, this ties the shafts to their own treadles, so that more than one treadle may need to be engaged depending on the lift work. 

8-shaft skeleton tie-up for a countermarch loom.
O = rising shafts, X = sinking shafts. Details here.

Advantage to method 2
  • Don't have to re-tie the lamms and treadles again
Disadvantage
  • Footwork is more complicated

Method 3: Tie-up from the top of the lamms

This method was described in the October 2017 issue of Complex Weavers Journal. I found several blog posts and videos on it, and made a blog series about it:

Next time I warp the loom, I'll do a step-by-step on tying up the treadles to the lamms from the top.

© 2024 by Leigh at Leigh's Fiber Journal
Dressing the Glimakra B2F Step 6: Checking the Shed, Weaving a Header

Sunday, May 19, 2024

Dressing the Glimakra B2F Step 3: Winding on the Warp

Continued from Dressing the Glimakra B2F Step 2: Loading the Raddle

With this step, I was in more familiar territory. I just need to adjust it to this particular loom.

1. Tensioning the warp

Should the warp be weighted, and if so, how? There are different schools of thought here.
  • No weights, tension by manually tugging on the warp after each rotation of the beam. (Chandler)
  • Applying resistance with weights or another mechanism such as a warping drum or another person. (Osterkamp). In fact, Peggy basically states the more tension during winding on, the better (although she also gives instructions for the no-tension method).
Once upon a time I used half-gallon milk jugs, which I don't get anymore because we have our own goat milk. But I did have some empty gallon vinegar jugs and used these plus a distilled water jug. 

For my personal notes: each jug weighs 8.5 pounds.

2. Winding on

The idea is for the warp to wind onto the warp beam the same width as in the raddle.

Detangle as needed by snapping the warp. 

Tangles at the raddle can result with broken threads; snapping the warp works them out.

Insert packing sticks at regularly spaced intervals to cover apron cords. This prevents the knots from making lumps in the warp.


Rolls of paper can be used instead, but the sticks came with my loom, so I use them.

Of course the weights have to be re-positioned as the warp is wound on. 

I left enough in front for threading, sleying, and tying onto the front apron rod. Then it was time to . . .

3. Remove the raddle


Now I'm ready to thread the heddles.

Notes and Observations
  • There is plenty of room for improvement, which I'll work on in the future. At least I've made a start.
  • The bunching of the warp bouts is a concern as it creates V shapes with the warp. Osterkamp recommends the following to prevent variations in tension due to the angle the warp is winding onto the beam
    1. Insert lease sticks into the threading cross and remove the choke ties.
    2. Then put an end stick into the threading end loop and spread the warp out to the proper width.
Dressing the Glimakra B2F Step 4: Threading, Sleying, Lashing On
 

Friday, May 17, 2024

Dressing the Glimakra B2F Step 2: Loading the Raddle

Continued from Dressing the Glimakra B2F Step 1: Measuring the Warp

First question: where to load the raddle? At the loom or on a table and then carry it to the loom?
Second question: where to place the raddle at the loom?

There are a variety of answers to these questions, all of which reflect the preferences of different weavers and the types of looms they have. My choices are my experiments, to be tweaked in the future as it suits me.

1. Set up the loom

Considering the size and weight of my raddle, plus the amount of room I have to work in, I opted to load the raddle at the back of the loom. Here is my set-up.


a. Support sticks rest on the front and back beams.

b. Lease sticks to secure the raddle lease (cross).

c. Raddle is as as close to the back beam as possible. Peggy Osterkamp recommends this as the best position to help ensure that the warp winds on at the same width as on the raddle.

d. End stick

Note: I later fine tuned the set-up because I found the lease and end sticks slid around too much as I worked with the warp. Here's what I did about it, and what I'll do next time . . .

With shoe laces, the end stick is tied to the back beam
and the lease sticks are tied to the gable of the loom.

One "problem" is my double back beam, as it's somewhat in the way. I considered removing it, but that would be another step, and I don't have a place to put it at the moment. I decided to try and work around it. I'll adjust if necessary. 


2. Insert lease sticks into the raddle cross.

Bouts spread out on lease sticks.

Lease sticks tied together to prevent warp from slipping off.

3. Insert end stick into the raddle end of the warp.


This is where it came in handy to have used different color choke ties for the upper and lower sides of the cross. Otherwise, I might have twisted some of the bouts when I put them on the end stick.

After the bouts are on the end stick, the choke ties are removed.


4. Distribute the raddle groups in the raddle.

I had 88 raddle groups of 4 threads each, so I counted out 44 raddle dents from center to begin laying them in, starting starting at one end and working to the other.

5. Attach the end stick to the back apron rod or transfer warp to apron rod.

Here, they are tied together with stout string, starting in the middle
of the warp and working outward with new ties every 3 or 4 inches.

I found tying the rods together to be tedious and time consuming. Next time, I'll try transferring the warp from the end stick to the apron rod. 

6. Remove the lease sticks.

7. Secure the raddle.

Ready for the next step

Options for raddle placement are as varied as there are weavers. Chandler puts her's on the breast beam, while Osterkamp recommends as close to the back beam as possible. I was able to tie mine onto the back of the loom.

My conclusion about the second back beam is to remove it, unless I'm going to use it. While it was only mildly inconvenient to have it on the loom, I think it would be easier to warp without it. 

Now, I'm ready to wind the warp onto the back beam.

Dressing the Glimakra B2F Step 4: Threading, Sleying, Lashing On

Wednesday, May 15, 2024

Dressing the Glimakra B2F Step 1: Measuring the Warp

Tucked away in my copy of Tying Up the Countermarch Loom by Joanne Hall, I found the notes I'd once  written about how to warp the Glimakra back-to-front (B2F). 47 steps! And none of it rings a bell. Eek! My first impulse was to go to YouTube, where I found a few videos, but those still left me with questions. Next, I read through my blog posts on warping back-to-front. My Warping the Glimakra: Winding It On post had some helpful notes, photos, and comments from readers. But it wasn't enough to take me through the process, so I pulled out Chandler's Learning to Weave and Osterkamp's first two volumes of her New Guide to Weaving series, and started reading.

The purpose of this series is to write a guide for myself. I want to detail the steps for next time and as many times as it takes afterward until it becomes second nature to me again. Maybe it will be helpful for someone else too. I will likely modify this as I try variations, so suggestions and tips are welcome!

Knot notes
  • (Osterkamp) Use a double half hitch at beginning and end of warp. After the warp is measured, cut the end of the loop and slip the tail off.
  • Keep all knots at threading lease end of the warp, as this is where the threads must later be cut apart for threading the heddles. I.e., the raddle end loop needs to remain intact for securing the warp onto the end stick.

1. Mark the warp path with a guide string and measure the warp. 

I decided to try Osterkamp's method of 2 leases (crosses).

At one end is the thread-by-thread lease for threading the heddles

At the other end is the raddle lease. It groups warp according to sett and raddle sections.

Raddle lease example: for this project, the sett is 8 e.p.i., and my raddle sections are ½ inch. So my raddle lease groups are four warp ends (threads) each. 

2. Keep track by counting the raddle groups.

My raddle groups were 4 ends each, so I chose to count them in groups
of 5, or 20 ends per group. There are 100 warp ends shown here.

Warping Board Tips: 
  • Don't allow warp ends to overlap on the pegs (creates uneven lengths)
  • Keep bouts (sections of warp) to no more than 1.5 to 2 inches in width (pegs tend to pull in as they fill with warp, creating uneven lengths).
Warp ends not overlapping. About 1.5 inches total width.

3. Secure crosses with choke ties. For a long warp, also secure 1 yard sections with ties.

Threading lease tied off
Tying Tips:
    • Use two ties per peg.
    • Don't catch the guide string in the ties.
    • Use different color ties to notate threading and raddle ends of the warp, also top and bottom of the warp.

4. The raddle is threaded first, so chain the warp starting at the threading cross end.
Dressing the Glimakra B2F Step 2: Loading the Raddle
Dressing the Glimakra B2F Step 4: Threading, Sleying, Lashing On
Dressing the Glimakra B2F Step 5: Tying Up the Lamms & Treadles