Showing posts with label natural dyes. Show all posts
Showing posts with label natural dyes. Show all posts

Tuesday, October 01, 2024

Natural Dyeing: Goldenrod

Two weekends ago, I took my goats for a walk in the woods and noticed that the back of my neighbor's field full of goldenrod. How could I pass that up?


The next day I took a short walk to collect some. Along the way, I passed a couple of busy turtles.


My idea for the goldenrod was to try it in an all-in-one dyebath. This is where the mordant is added directly to the dyepot rather than mordanting as one step, then dyeing as another. It was a common way to dye, once upon a time. Now, the tendency is to do large batches of fiber to have ready for future dye projects. The appeal to the one-pot method is saving on water, time, and energy by doing it all at once. 

So that was my plan. HOWEVER, after I got it going, I realized that the time requirement for mordanting was 60 minutes, while the timing for the best goldenrod yellow was only 10 minutes. I didn't think 10 minutes was enough time for the fiber to absorb the mordant, so my dyebath went for the full 60 minutes. 

Preparing the dyebath


  • Recommended amounts are equal parts flowers to fiber. 
  • Bring to a simmer
  • Simmer for 30 to 60 minutes
  • A low simmer is said to bring out the clearest yellow (Dean)
  • Let cool overnight
  • Strain

Preparing the all-in-one dyepot


  • Mix the mordant in a jar of hot water until dissolved
  • For 8 ounces of wool fiber I used
    • 2 tbsp alum
    • 2 tsp cream of tartar
  • Add to dyepot and stir well
  • Add fiber and bring to a simmer
  • For goldenrod, both Dean and Buchanan recommend 10-15 minutes for the purest yellow
  • Longer simmering is said to bring out the greenish tints.

Results


I'm not sure how accurately that portrays what I got, but in real life, it's a very pretty light yellow, even with the longer simmering.

Modifiers

I divided my dyed fiber into three roughly equal portions for two afterbath experiments: one with iron, the other with copper.

Iron afterbath

I recently purchased ferrous sulfate (iron) from Amazon and wanted to give it a try!
  • Remove fiber from dyebath and set aside
  • Mix ferrous sulfate powder in hot water
    • Amount: scant teaspoon (one quarter the amount of a regular mordant bath)
  • Stir into dyebath
  • Add fiber and heat to a simmer
  • Simmer 30 to 60 minutes
  • Cool overnight
  • Remove fiber, wash, and dry

Iron is said to "sadden" color, so I guess green is a sad yellow.


For this one, I first used some of the decanted copper solution I used to mordant fiber for hardy hibiscus. I was doubtful there was enough copper left in it to make a difference, however. I followed the same procedure as for the iron afterbath. 

copper afterbath using decanted copper mordant solution

Comparison: original goldenrod on left, same with copper modifier on right

I debated whether to leave it at that or try a stronger copper solution. The weak solution only seemed to muddy the yellow, which I don't find very appealing and didn't give me good information concerning the potential of the afterbath. So I added an eighth dose of copper sulfate to the copper afterbath and put the fiber back in. It simmered for about 30 minutes or so.

second copper afterbath with more copper

A much more pleasing change of color, don't you think? 

Here's a side-by-side comparison of the day's final results.

Left: goldenrod, no modifier. Center: iron modifier. Right: Copper modifier.

Monday, September 16, 2024

Natural Dyeing: Hardy Hibiscus (With Copper Mordant)

I know I said I was done with hibiscus flower dyeing, but they are still blooming profusely and I couldn't resist trying it with a different mordant. The first time I tried it with alum and cream of tartar, the second time with no mordant, and this time with copper as the mordant. Directions for mordanting fiber or yarn with copper can be found here.

Preparing the dyepot

I followed the same procedure as previously, but I scaled down the amounts.

For this experiment, I used 4 ounces of hibiscus flowers
  • Amounts
    • 4 ounces fresh hibiscus flowers
    • 4 ounces clean, mordanted fiber
  • Pour boiling water over the flowers
  • Simmer flowers for about 30 minutes.
  • Strain

Dyeing the fiber
  • Add the wet, mordanted fiber to the dyebath. 
  • Heat to a simmer
  • Simmer 30 to 60 minutes
  • Let steep until cool (I left it overnight)
  • Wash with a bit of mild detergent and rinse until no more color exhausts from the fiber.
Results


And to compare, here are my previous hibiscus dyeing experiments.

Left: hibiscus with alum mordant. Center: undyed. Right: hibiscus without mordant.

So, apparently I can get silver and gold from hardy hibiscus flowers, but not what the natural dye books say, which is purple.

Saturday, September 14, 2024

Natural Dyeing: Copper as Mordant & Modifier

Copper = copper sulfate or blue vitriol

Solutions of copper for mordanting or modifying can be made it two ways: with copper sulfate powder or crystals, or with scraps of copper pipe, wire, etc. The directions here are for animal fibers: wool, silk, angora, cashmere, mohair, llama, alpaca, etc.

Mordant made with copper sulfate powder or crystals

The purpose of a mordant is to fix the dye color to the fiber. Copper sulfate is a common one and can be purchased almost anywhere that sells gardening or pond supplies because it's used as an herbicide, fungicide, to control algae in ponds, and as a soil additive for copper deficient soils. I use it in my Pat Coleby mineral mix for my goats because it's an essential element for goats. Copper in large amounts is a poison, so one has to use their "smarts" when handling it.

As with recipes for an alum mordant, I found a variety of recipes for copper mordant as well. Recommended amounts range from 2 to 8% copper sulfate of the weight of goods (WOG). Jenny Dean uses vinegar in her copper sulfate recipe. I don't have a very good scale, so I decided to rely on Rita Buchanan's quick method measurements:
  • 2 tablespoons copper sulfate 
  • per 1 pound dry goods
copper sulfate diluted and ready to make the mordant bath

Procedure
  • Soak the fiber, yarn, or fabric to be dyed in a large pot of clean water
    • Start with thoroughly scoured goods because oils or processing residues can interfere with the uptake of any mordant.
    • Let soak at least a couple of hours, to ensure thorough wetting for an even uptake of the mordant.
  • Prepare the copper solution
    • Dissolve in a small amount of hot water.
  • Prepare the mordant solution
    • Dilute the dissolved copper solution in a sufficient amount of water, typically 4 gallons for a pound of goods. There needs to be enough water to float the yarn or fiber with plenty of room.
  • Remove the fiber from its soaking pot and add to the mordant pot. Gently heat to a simmer, and hold at a simmer for about an hour. 
  • Let cool.
  • Remove the fiber and rinse thoroughly (gloves recommended). 
  • The fiber can be dyed immediately, or dried for future use.
Wool mordanted with copper has a green tinge

Re-using the mordant bath

I found instructions for this in Rita Buchanan's A Dyer's Garden. Because fiber or yarn doesn't absorb all of the chemical from the mordant bath, it's possible to re-use it by topping it off with additional chemicals.
  • Use 1/3 the amount of copper sulfate called for in the original recipe
  • Follow all the procedure steps above.
After mordanting, the copper solution can also be decanted into a closed bucket or jar and used again later.

Mordant made with copper pipe and such

I've not tried this yet, but I'm including the instructions for future use! Copper pipe, wire, or pennies can be used, as long as they are pure copper, not an alloy. 
  • Place copper scraps in a wide mouth jar
  • Add water and white vinegar (I've seen 1:1 and 2:1 ratios recommended). The vinegar is needed to make the copper soluble. 
  • Lid the jar and let sit for at least a week or two.
  • Decant the liquid off as needed and add to the mordant pot.
  • Add clean, wet wool
  • Heat to simmering and simmer for about an hour. The fiber should turn pale green.
  • Remove the fiber and rinse thoroughly.
  • May be used immediately of dried for later.
An alternative would be to do it the old-fashioned way by doing the dyeing in a copper kettle.

As a modifier

Modifiers are after-dye treatments used to alter the color. They are weaker solutions than mordant baths, and are a great way to extend the color range of any given dyestuff. Copper will make colors greener or browner, and generally improves the fastness of the dye color.

To use immediately:
  • Mix 1/4 amount of copper (as for mordant) in hot water
  • Remove the fiber from the dyebath and set aside.
  • Stir the copper solution into dyebath
  • Return the damp fiber to dyebath
  • Simmer for 15 to 30 minutes or until the color changes
  • Let cool overnight
To make a larger batch ahead of time:
  • Mix 1 tablespoon of crystals in 1 quart boiling water.
  • Store in an airtight jar.
  • This is enough to use for several afterbaths.

Discarding the exhausted mordant or modifier bath

I decanted and saved some of the mordant bath to try as an afterbath in future projects.


Then, because our soil is copper deficient, I was pleased to dilute the remainder and distribute it out on our pasture. Another option is to pour the diluted bath over a gravel driveway. 

 © September 2024 by Leigh at Leigh's Fiber Journal

Sunday, September 01, 2024

Natural Dyeing: Hardy Hibiscus (Without Mordant)


Previously, I showed you my results from dyeing with hardy hibiscus flowers using alum and cream of tartar mordant. Jenny Dean's Wild Color says it can be used without mordant, so that was next.  

I followed the same procedure as hibiscus dyeing with mordant, but I kept a closer eye on time and temperature. I also decreased the amount of flowers and fiber to four ounces each. It was easier to collect that amount and keep the flowers fresh in the fridge while I collected. 

Preparing the dyebath
  • Pour boiling water over the flowers
  • Bring to a simmer
  • Simmer flowers for about 30 minutes.
  • Strain

Dyeing the fiber

lovely color in the dyepot
  • Add the wet, unmordanted fiber
  • Heat to a simmer
  • Simmer 30 to 60 minutes
  • Let steep overnight as it cools 

The Results

This is after washing and drying.


Does it even look like there's a color change? It's hard to tell! Below is a comparison of undyed and hibsicus dyed samples from both experiments. The undyed sample is in the middle.

Left: hibiscus with mordant. Center: undyed. Right: hibiscus without mordant.

Interesting, considering how much color was left in the exhausted dyepot. 

exhausted dyepot after dyeing

I'll also mention that I washed the two samples with different soaps because hibiscus is supposed to be pH sensitive. For the mordanted fiber, I used soap berries. For the non-mordanted dye experiment, I used EOS unscented dishwashing liquid. The difference is in pH. Soap berries are slightly acidic, and dishwashing liquids are slightly alkaline. I can't say I see that it made a difference in the final color of the fiber samples compared to the color before washing. 

Analysis

Supposedly, hibiscus flowers dye animal fibers shades of purple. I had no such luck. Of the possible factors I mentioned last time, I can eliminate temperature and time. All other factors remain as possibilities. Gray is a natural fiber color, so I thought it was a lot of work for the color results. 

Different mordants might make a difference in the color results, as might after dips. Bit for now, so much for dyeing with hibiscus flowers. 

Friday, August 30, 2024

Natural Dyeing: Hardy Hibiscus (With Alum Mordant)


Also known as rose mallow, rose of Sharon, or althea. There are a variety of species in the genus. Mine are apparently hibiscus syriacus, and we have quite a few in the yard. Ours range from pale to dark pink and lavender. I have one solid white one. Some commercial hybrids come in red. The dark pink and red ones are said to be the best for dyeing.

Both of the natural dyeing books I'm referencing (Wild Color and A Dyer's Garden) give instructions for dyeing with hardy hibiscus, so I picked up tidbits from each.

Collecting the dyestuff

This was a bit of a challenge because I wanted 8 ounces but didn't have enough blooming at any one time to collect enough. One book says the flowers don't freeze or dry well, the other said they can dried. Rita Buchanan suggests picking every day or two and storing in the fridge in a plastic bag. This is what I ended up doing. By the time I had 8 ounces, the ones on the bottom were going bad so I had to discard them. I should have weighed what was left, but didn't think of it at the time. 

Preparing the dyepot


  • Pour boiling water over the flowers
  • Simmer flowers for about 30 minutes.
  • Strain

Dyeing the fiber


Jenny Dean's book shows color samples of hardy hibiscus dyed both with amd without a mordant. For this batch, I used alum mordanted fiber.

I had previously soaked some fiber and had it ready for the dyepot. This time, I didn't wait for the bath water to cool, but added the wet fiber to it while hot.
  • Add the wet fiber
  • Heat to a simmer
  • Simmer 30 to 60 minutes
  • Let steep overnight as it cools (can be left longer for deeper color)
Note: when first checked on the pot after putting it on the heat, it was at a rolling boil. I turned it down and left it in the dyebath for close to an hour.

The Results

Right out of the dyepot, still damp.

Nowhere near the lavender shades in the dye books!

Here it is after being washed, rinsed, and dried.


Analysis

I appeared to have good color in the dyepot, so what happened? Several things come to mind.
  • I was light on the dyestuff because some of the flowers had spoiled. Did I have too few flowers? Possible solution would be to collect fewer flowers and dye smaller quantities of wool. 
  • Did some of the spoiled flowers get in the dyebath and affect results?
  • Did the active boiling have anything to do with it?
  • Was it my water (dyed with city tap water)
  • Something else?
  • On the other hand, here's a quote from Rita Buchanan, A Dyer's Garden page 81.
"Dark hibiscus flowers give fascinating, impressive, but unpredictable colors . . . Every time I use this plant, I get different colors—lilac, purple, mauve, green, gray, brown, black—but they're all interesting and attractive."

In light of that, if I had been going for a light gray, I'd be pleased with the results. It is a lovely color. As it was, however, I was disappointed because I wanted something different. Maybe calling it silver-gray will take the edge off the disappointment. 😉

Definitely, more experimenting is in order.

Saturday, August 24, 2024

Natural Dyeing: Pear Leaves, Part 2


After the first experiment dyeing with pear leaves, there were several things that I was curious about. 
  1. Exhaust dyeing
  2. Afterbath (copper)
  3. Will the leaves release more color in subsequent dyepots as Dean suggests in her book?
I have several pear trees, so this information might be good to know for future reference. 

I started by dividing the leftover dye water into two pots, amounts about equal. One, I used for the exhaust dyeing experiment, the other for the afterbath experiment. I used half the amount of alum mordanted fiber for each experiment, thoroughly soaked in water before adding to the dyepot. 

To compare results, here is the sample from the original pear leaf dyepot.

original dye color

1. Exhaust dyeing

This is simply reusing the same dyepot after some / most of the color has been taken up in the original dye job. I used 4 ounces of mordanted fiber for this experiment, but followed simmering and soaking times roughly the same as the original dye lot.

exhaust bath dye color

2. Copper afterbath

Or maybe it's afterdip. I dissolved  a rounded half-teaspoon of copper sulfate into the other half of the original dyebath and added 4 ounces of fiber from the original dye lot.

original dyed fiber with copper afterbath

Here's a comparison of the original dyed fiber and my first two experiments.

Left: copper afterbath. Middle: original dye color. Right: exhaust dyed fiber.

3. Re-using the pear leaves

This idea came from  Jenny Dean's book. In her general instructions for extracting color from plant leaves (page 48) she states,

"The leaves reserved from the first color extraction can be simmered again."

That roused my curiosity and I decided to try this with the pear leaves from the original dye bath. I followed the same procedure, but used half as much fiber in the dye pot. Here's what I got . . .

color from re-used pear leaves

It's very similar to the exhaust dyed sample, but I think it's a clearer yellow, i.e. a little less gold. From my reading I'm understanding that different pigments in the dyestuffs are released at different times and temperatures. I don't know if this would consistently be true for pear leaves, but it's an interesting tidbit to keep in mind for future reference.

I'm not sure if the camera and computer do the difference justice, but here are the similar samples side by side.

Left: exhaust bath fiber. Right: re-used leaves dyed fiber.
In hand, the exhaust dyed have a more golden nuance.

So, lots of color from pear leaves. Further experiments could include different mordants and afterbaths. For these, I need to get iron to try for mordanting and dipping. 

In addition to the leaves, the bark is said to yield a pinkish-purple color. I'll have to try that one too, if I can figure out how to harvest bark without hurting the tree. 

Thursday, August 22, 2024

Natural Dyeing: Pear Leaves, Part 1


After two dyeing projects that took repeated simmering and steeping to extract the color, I was ready for something a little simpler. I reckon natural dyeing is a summer project for me, when fresh plant material is widely available. I'm trying to take advantage of seasonal resources while I can. The directions for using pear leaves came from Jenny Dean's Wild Color.

Her recipe calls for at least equal weight of leaves to fiber. More, for stronger color. Color can be extracted by either cold soaking or simmering. I will have to try the cold method sometime, but for now, I'm thinking I'd get stronger color with heat, so that's what I opted to do. 

Day 1: Making the dyebath


  • Dyebath amounts should be at least 1:1 for leaves to fiber. I used:
    • 12 ounces pear leaves for 8 ounces fiber
    • 2 gallons water
  • Pour boiling water over the leaves and let sit. 
  • Or, place leaves in several gallons of water, bring to a boil, and simmer for an hour or two. 
  • Let steep overnight until cool.
Note: the leaves smelled like cooking spinach while they simmered. 

Day 2: Dye day

  • Strain out the leaves (and save for another dyeing experiment).
  • Add thoroughly wetted, mordanted fiber to the pot. (I used alum and cream of tartar.)
  • Simmer for 30 to 60 minutes or so, until desired color is reached.
  • Let steep overnight until cool.

Day 3
  • Remove the fiber
  • Wash with mild dish detergent and rinse until the water is clear.
  • Squeeze out excess water (or run through the spin-only cycle in the washing machine) and lay out to dry. 

The bark of the pear tree can also be used for dyeing and gives pinkish/purplish colors. I'll have to give that a try sometime in the future. Next, however, I wanted to experiment a bit with this dyebath and see what other colors I could get.


Related posts

Saturday, August 17, 2024

Natural Dyeing: Black-Eyed Susans, Part 2


Day 4: Dyeing the fiber


  • Dye day!
  • Soak 8 ounces of mordanted fiber in water for about an hour or so
  • Strain the flowers out of the dyepot
  • Add wet fiber
  • Heat to simmering
  • Let simmer one hour
  • Cool overnight
Day 6

I didn't mess with it until the following Monday. Long soaks for best color are recommended for Rudbeckia anyway. 
  • Hold breath
  • Remove the fibers from the pot
  • Behold the results

Not what I was hoping for. Not even terribly interesting for a dye experiment. Some sheep breeds have similar colors naturally. The hoped for color with black-eyed susans is olive green, and tan is pretty much a "fail" color. Here is a comparison of results from Buchanan's A Dyer's Garden and Dean's Wild Color, along with mine. 


So what happened? A common explanation is a weak dyebath, except mine was twice the weight of flowers to fiber. Another explanation is not enough time simmering and soaking. Considering how many days I gave this, I'm not sure that's it either.
  • Was it from the mishap making the dyebath?
  • Using late season flowers? I picked the second flush of flowers, did that make a difference?
  • The variety of flower?
  • Growing conditions?
  • Not enough rain?
  • My soil?
  • My water?
But because the results weren't terribly impressive to me, I decided not to see what an exhaust bath would give me. Instead, I decided to try an afterbath of copper solution. Our soil is copper deficient, so I keep copper sulfate powder to add to my mineral supplement for my goats. It's also sold as a soil amendment for copper deficient soils. 
  • Mix 1/4 amount of copper in hot water
    • Standard amount for 1/2 pound fiber is 1 tablespoon copper
    • 1/4 amount is therefore 3/4 tsp copper
  • Stir copper solution into dyebath
  • Return damp fiber to dyebath
  • Simmer for 15 to 30 minutes or until the color changes
  • Let cool overnight
Day 7
  • Remove fiber
  • Wash with a little dishwashing liquid and rinse until water is clear.
  • Let dry
Here is a side-by-side comparison of my two experiments.

Left: original experiment, mordant only.
Right: Same fiber with copper afterbath.

I was thinking the copper might make the fiber greener, but it just seemed to make it darker.

Another afterdip could be an iron solution, which I didn't try. It can be made with rusty nails and vinegar, or with ferrous sulfate purchased from the gardening department (as an amendment for iron poor soils). I have neither of these and was done experimenting with black-eyed susans anyway. Both copper and iron can be used as mordants too, for different color results. And that raises a question.

Will I try dyeing with black-eyed susans again? 

I'm ready to move on at this point, but perhaps next summer, when the flowers can be harvested earlier in the season. The plant (without the flowers) is said to yield a different color. Do I want to experiment more? It was a lengthy project, so I honestly don't know. Is there another way to get green? Of course there is, so it's a matter of whether I'm determined to see if I can do it, or is it worth it? Right now, no. In the future, who knows?

Thursday, August 15, 2024

Natural Dyeing: Black-Eyed Susans, Part 1

The dyeing bug has bitten. It was my successful pokeberry dyeing experiment that did it. In pouring over my several natural dyeing books, I realized that I have a lot of free dyestuffs growing on our property, and that I'd better get a move-on because fresh plants work best but our growing season is getting late in its offerings. I've missed out on some things, but I still have a lot to experiment with. 

One thing I wanted to try was black-eyed susans. 

Black-eyed Susans, Rudbeckia species

According to the books, different parts of the plant give different colors. I decided to focus on the flowers, which are said to make an olive green with a sufficiently strong dye bath. That means a high ratio of dyestuff to fiber and giving it long simmering and soaking times. A weak dyebath is said to yield tan. From reading others experiences, however, this all isn't a guarantee, so I'll just have to give it a go and see what I get. The first step (part 1) is to make the dyebath. 

Day 1: Making the dyebath (Days 1 - 4)

  • Dyebath amounts:
    • 1 pound flowers (for half-pound of fiber)
    • 1.5 - 2 gallons boiling water
  • Pour the boiling water over the flowers and let steep overnight.
Note: my actual steep time was about 24 hours.

Day 2

  • Bring to a full boil
  • Boil (not simmer) for one or two hours
  • Let cool overnight
Confession! The pot was boiling nicely when I went outside to do some things. When I came back in, almost all of the water had boiled out! Fortunately, it didn't burn, and I immediately poured in two more kettlesful of boiling water. Now I'm uncertain about the color, but I'm going ahead to experiment. Hopefully, I'll still get something nice!

Day 3
  • Bring back to a boil
  • Simmer for several hours
  • Cool overnight

Day 4


  • Strain out the flowers
  • Ready to dye.

Monday, August 12, 2024

Natural Dyeing: Alum Mordant For Animal Fibers

Alum = potassium aluminum sulfate
Cream of tartar = tartaric acid
Animal fibers include wool, silk, angora, cashmere, mohair, llama, alpaca, etc.

Alum is fairly easy to find, as it has a number of common uses: as soil conditioner for acid loving plants, in water treatment, for pickle making. 

Cream of tartar is commonly used as a cooking additive: for homemade baking powder, to stabilize egg whites in meringues, in winemaking, even as a natural cleaner.

In natural dyeing alum is used as a mordant. The purpose of a mordant is to fix the color to the fiber. With alum, the cream of tartar assists in the take-up of the alum in animal (protein) fibers. 

In researching, I find I have three books on the topic and four different recipes.

Jenny Dean (Wild Color)

  • 8% alum per weight of fiber
  • 7% cream of tartar per weight of fiber
So, for 1 pound fiber or yarn that comes to 
    • 1.28 oz alum
    • 1.12 oz cream of tartar

  • 1 pound wool
  • 4 oz. alum
  • 1 oz. cream of tartar

Rita Buchanan (A Weaver's Garden)

Quick recipe
  • 1 pound wool
  • 4 tbsp alum
  • 4 tsp cream of tartar
Technical recipe
  • 14% alum per weight of fiber
  • 4% cream of tartar per weight of fiber
For one pound of wool that comes to:
      • 2.24 oz alum
      • 0.64 oz cream of tartar

Quite a bit of variation! But which is correct? Which is best?

Since I lost my notes from my previous natural dyeing experiments, I opted for the easiest recipe - Rita's quick recipe so I wouldn't have to figure out percentages. For my records, here's what I did

Procedure
  • Thoroughly wet the fiber. Soak in clean cool water for an hour or two
  • Measure chemicals into a glass jar and mix with boiling water until dissolved.
  • Add to 4 gallons of cold water; mix well.
  • Add wet fiber
  • Heat slowly to a simmer and simmer one hour.
  • Allow to cool.
  • Remove fiber.
  • Rinse and either dye immediately or dry for later use.

Re-using the mordant bath

I found this in Rita Buchanan's A Dyer's Garden (which I like better than A Weaver's Garden, except it appears to be out of print. It's still available, but who in their right mind is going to pay that kind of price???) Anyway . . .

Because the fiber or yarn doesn't absorb all of the chemicals from the mordant bath, it's possible to re-use them by topping them off with additional chemicals.
  • Use 1/3 the amount called for in the original recipe
  • Follow all the procedure steps above.

Discarding the exhausted mordant bath

Potassium aluminum sulfate is commonly used as a soil conditioner for acid loving plants such as blueberries or azaleas. The spent mordant bath can be used to water any acid loving plant. 

Thursday, August 01, 2024

Non-fading Pokeberry Dye Part 2

Continued from Part 1

My dyed but not yet rinsed pokeberry fiber was left to oxidize for several days to set the color. Carol Leigh recommended a couple of hours, but one dyer observed that the longer it sits, the better the dye adheres to the fiber. (See "recipe resources" in part 1) That statement was noteworthy, I thought, and worth a see-for-myself experiment, so I wasn't in a hurry to rinse the fleece.

Day 8

  • Soak in several rinse waters to remove excess dye (do not use soap or anything alkaline at this point).

  • Rinsing with rainwater from one of our rainwater collection tanks.
  • Once the rinse water is clear, squeeze out excess water and let dry thoroughly

Notes:
  • Actual amount of time between dyeing and rinsing was 7 days. 
  • Fresh pokeberry dye is still sensitive to pH, so to keep vibrant color, soap or detergent, which lean toward the basic range of the pH scale, are not used at this point.
  • It's also sensitive to sunlight, so keep out of sunlight. 

As to the dyepot, the color hadn't completely exhausted and there was still a lot of color in the bath. 


I couldn't bring myself to discard it, so I mordanted more fiber and popped it into the exhaust bath and proceeded with the same steps as before. The exception was that I used 4-ounces of fiber instead of 8. Doing this accomplishes two things. One is "waste not want not" as I can get more dyed fiber. 

The second, is a chance to experiment with the mordant bath. My thinking was that the vinegar is diluted anyway, so the percentage of acetic acid in the bath could be adjusted simply by adding more of a weaker product, right? That way I could simply adjust the amount of common vinegar to get the same results. I couldn't find a formula to calculate this precisely, so I ball-parked it.

Exhaust bath #1

For this experiment, the amounts for the mordant bath were:
  • 4 ounces washed fiber
  • 1.5 gallons water
  • 1 quart 5% acetic acid (household vinegar)
I followed the same instructions to mordant and dye the fiber.


Obviously, there was still a lot of color in the dyebath!

Exhaust bath #2
  • Used same acid mordant bath, adding another pint of 5% vinegar
  • 4 ounces of fiber
  • Added a second pint to the dyebath too.

Exhaust bath #3
  • Started with a fresh mordant bath of 1 quart 5% vinegar to 1 gallon water
  • 4 ounces of fiber
  • no additions to the dyebath

As you can see, I got a lot more color out of the dyepot. Possibly, I could have tried one more because the dyepot water still wasn't clear. But this is where I decided I was finished. 

Here are all the samples side by side.


I got a lot of color from that dyepot! 

Would I try pokeberry dyeing again? Absolutely. Apparently, color depends on temperature, so that would be fund to experiment with. Likely, I'll collect another batch of pokeberries to freeze for more dyeing fun next year.